What is the Stokes Germany Rear Stabilizer Link Rod Set for Mercedes-Benz CLA C118?
The Stokes Germany Rear Stabilizer Link Rod Set is a premium European-quality suspension replacement set of 2 designed for the applicable Mercedes-Benz CLA C118 rear suspension and corresponds with OEM reference A2473205300. These rear stabilizer link rods provide an important mechanical connection between the relevant rear suspension components and the anti-roll bar while allowing normal suspension movement during everyday driving. They are also commonly known as rear sway bar links, sway links, anti roll link rods, anti-roll bar links and stabiliser sway links, so customers may find different terminology when checking spare-parts catalogues or speaking with workshops. Every time the Mercedes-Benz CLA C118 travels over potholes, speed breakers, road joints, broken roads or uneven surfaces, the rear suspension moves and the stabilizer links repeatedly articulate as part of the suspension system. The links also operate during cornering because suspension movement and mechanical loads can differ between the left and right sides as the vehicle changes direction. Because these components repeatedly move whenever the rear suspension operates, they experience thousands of movements throughout normal vehicle use. They are also exposed to road vibration, impacts, dirt, moisture and changing mechanical loads. Over extended mileage, these operating conditions can gradually create mechanical wear and unwanted clearance inside the original link joints. Once excessive joint play develops, worn rear stabilizer links may contribute to knocking, clunking, tapping or rattling noises from the rear suspension, particularly when the CLA is driven slowly over rough roads, small potholes or speed breakers. Replacing genuinely worn links helps remove unwanted movement caused specifically by these components and restores their proper mechanical connection within the rear stabilizer system. Stokes Germany provides a premium replacement option for Mercedes-Benz owners looking for European-quality steering and suspension components with emphasis on dependable construction, accurate vehicle-specific fitment and practical replacement value. Correct diagnosis remains important because rear anti-roll bar bushes, suspension arms, suspension bushes, dampers, mountings and other suspension components can produce similar symptoms. Always verify OEM reference A2473205300 against the complete 17-character VIN and exact Mercedes-Benz CLA C118 suspension specification before ordering or installation.
What are the common symptoms of worn rear stabilizer links on a Mercedes-Benz CLA C118?
Worn rear stabilizer links on a Mercedes-Benz CLA C118 can cause or contribute to several noticeable suspension symptoms, with knocking, clunking, tapping or rattling noises from the rear suspension being among the most common reasons to inspect these components. The rear sway bar links operate whenever the suspension moves, which means their joints repeatedly articulate during normal everyday driving. When the CLA C118 travels over potholes, speed breakers, broken roads, road joints or uneven surfaces, each rear wheel responds to changes in the road and the stabilizer links move as part of the suspension system. During cornering, the sway links also experience changing mechanical loads because suspension movement can differ between the left and right sides of the vehicle. Over thousands of kilometres, repeated suspension movement, road vibration and impacts can gradually create mechanical wear inside the link joints. Once excessive clearance develops, a worn anti roll link rod may move slightly whenever the suspension changes position, direction or load. This unwanted movement can produce a noticeable knocking or clunking sound from the rear suspension. Smaller amounts of joint wear may produce lighter tapping or rattling noises. These sounds can become particularly noticeable when the CLA is driven slowly over rough roads, potholes or speed breakers because individual suspension movements are easier to hear. The rear suspension may also begin to sound less solid or refined when significant joint wear has developed. However, hearing a knocking or rattling noise does not automatically prove that the stabiliser sway links are defective. Several other components within the Mercedes-Benz CLA C118 rear suspension can produce similar symptoms. Rear anti-roll bar bushes, suspension arms, suspension bushes, dampers, mountings and related hardware should therefore also be inspected. A technician should physically check both rear stabilizer links for excessive joint movement, damaged protective components, loose mounting points, deterioration, corrosion or other physical damage. If one link is badly worn, the corresponding component on the opposite side should also be inspected because both generally experience similar overall mileage and road conditions. Correct diagnosis is important because installing new rear sway links cannot correct a suspension noise caused by another defective component. This Stokes Germany product is supplied as a set of 2. Always verify OEM A2473205300 against the complete vehicle VIN before ordering.
Which OEM number does this Stokes Germany rear stabilizer link set replace for Mercedes-Benz CLA C118?
This Stokes Germany Rear Stabilizer Link Rod Set corresponds with the provided Mercedes-Benz OEM reference A2473205300 for the applicable Mercedes-Benz CLA C118 rear suspension, and this OEM reference should remain exactly as provided when preparing the product listing, checking compatibility or ordering the replacement components. OEM numbers are particularly important when identifying Mercedes-Benz suspension parts because vehicles within the same model family can sometimes use different components according to production specification, engine, drivetrain, suspension configuration, equipment package or other vehicle-specific details. For this reason, simply knowing that the vehicle is a Mercedes-Benz CLA C118 should not be treated as the only compatibility check. Customers may also find this component under several different descriptions depending on the manufacturer, workshop or spare-parts catalogue. Common descriptions include rear stabilizer link, rear sway bar link, sway link, anti roll link rod, anti-roll bar link and stabiliser sway link. Because terminology can vary, checking OEM reference A2473205300 provides a stronger method of identifying the required replacement component than relying only on the general product description. Before purchasing this Stokes Germany set, the complete 17-character VIN should ideally be checked through an appropriate Mercedes-Benz electronic parts catalogue or provided to an experienced Mercedes-Benz spare-parts specialist. The rear stabilizer-link reference returned for that exact vehicle should then be compared carefully with A2473205300. If the original links remain installed, their identifying markings can also be checked wherever visible. If the original components have already been removed, the workshop can additionally compare their dimensions, mounting arrangement, joint positions, thread details and physical construction with the replacement links before installation. Visual appearance alone should never be treated as final compatibility confirmation because two suspension components can appear very similar while having different dimensions, mounting details or applications. If A2473205300 has been revised or superseded for a particular vehicle specification, that relationship should also be confirmed through vehicle-specific parts data rather than assumed. Correct VIN and OEM verification helps reduce incorrect orders, unnecessary returns and additional workshop labour. Therefore, retain A2473205300 exactly as supplied and verify it against the exact Mercedes-Benz CLA C118 before installation.
Should both rear stabilizer link rods be replaced together on a Mercedes-Benz CLA C118?
Replacing both rear stabilizer link rods together on a Mercedes-Benz CLA C118 can be a practical repair when both existing components have covered similar mileage and show comparable mechanical wear, which is also why this Stokes Germany product is supplied as a set of 2. The left and right rear sway bar links operate within the same stabilizer system and generally experience the same overall vehicle mileage, although their exact condition can differ depending on pothole impacts, road quality, driving conditions and previous suspension repairs. Every time the CLA C118 travels over potholes, speed breakers, broken roads, road joints or uneven surfaces, the rear suspension moves and the stabilizer links repeatedly articulate. During cornering and directional changes, the anti roll link rods also experience changing mechanical loads because suspension movement can differ between the left and right sides. Over extended use, repeated articulation, vibration and road impacts can gradually create mechanical wear inside the joints. If one link develops excessive joint play, damaged protective components, deterioration or another mechanical problem, the component on the opposite side should also be inspected because it has generally experienced similar mileage and operating conditions. This does not mean both stabiliser sway links must automatically be replaced every time only one component becomes defective. The actual mechanical condition of both sides should determine the repair. However, when both components show noticeable wear or have covered substantial mileage together, replacing them during the same repair can be practical. Installing a matching pair means both sides receive replacement components at the same time rather than leaving one heavily used link beside one new component. During replacement, the technician should also inspect the rear anti-roll bar bushes because worn bushes can create knocking or rattling noises similar to worn stabilizer links. Suspension arms, suspension bushes, dampers, mountings and related hardware should also be checked for excessive movement, deterioration or damage. If another suspension component is responsible for the noise, installing new rear sway links alone will not solve the problem. Correct installation is equally important, and all mounting points and related hardware should be properly inspected and secured. For this Stokes Germany set, the supplied OEM reference is A2473205300. Always verify this reference against the complete VIN and exact Mercedes-Benz CLA C118 suspension specification before installation.
Can worn rear sway bar links cause knocking or clunking noises in a Mercedes-Benz CLA C118?
Yes, worn rear sway bar links can be one possible cause of knocking, clunking, tapping or rattling noises from the rear suspension of a Mercedes-Benz CLA C118, particularly when the vehicle travels over potholes, speed breakers, broken roads, rough surfaces or uneven road joints. The rear sway links articulate as the suspension moves while maintaining the required mechanical connection with the anti-roll bar. When their joints remain in good mechanical condition, they allow the necessary suspension movement without excessive unwanted clearance. During everyday driving, however, these components repeatedly move as the rear wheels respond to changes in the road surface. Every pothole, speed breaker and uneven road section can create additional suspension movement, while cornering creates changing mechanical loads through the stabilizer system. Over extended mileage, this repeated movement can gradually create mechanical wear inside the joints. Once excessive clearance develops, an affected anti roll link rod can move slightly whenever the suspension changes direction, position or load. This unwanted movement can create an audible knock or clunk from the rear suspension. Smaller amounts of wear may produce lighter tapping or rattling noises instead. These sounds can become particularly noticeable when the CLA is driven slowly over uneven surfaces because individual suspension movements are easier to hear. However, a knocking sound alone should never be treated as definite proof that the stabilizer links have failed. Several other components in the Mercedes-Benz CLA C118 rear suspension can produce similar symptoms. Rear anti-roll bar bushes can develop wear and allow unwanted movement. Suspension-arm bushes and joints can also develop clearance. Damper components and their mountings may create noises, while loose suspension hardware can produce knocking even when the major components remain usable. A technician should therefore inspect the complete rear suspension before deciding which components require replacement. Both stabiliser sway links should be physically checked for excessive joint play, damaged protective components, loose mounting points, corrosion or other deterioration. If the links are confirmed as the source of the problem, replacing them helps remove unwanted movement caused specifically by those components. This Stokes Germany set provides 2 rear stabilizer link rods corresponding with OEM reference A2473205300. Correct OEM and VIN verification should always be completed before ordering or installation.
Why should I choose Stokes Germany rear stabilizer link rods for my Mercedes-Benz CLA C118?
Stokes Germany rear stabilizer link rods are positioned as a premium European-quality replacement option for Mercedes-Benz CLA C118 owners who want dependable suspension components with accurate vehicle-specific fitment rather than unknown low-cost aftermarket alternatives. This product is supplied as a set of 2 rear stabilizer link rods and corresponds with OEM reference A2473205300. Stabilizer links may appear relatively small compared with suspension arms, springs or dampers, but they perform an important function whenever the rear suspension moves. Their job is to maintain the required mechanical connection between the relevant suspension components and the anti-roll bar while allowing normal suspension articulation. Every time the Mercedes-Benz CLA C118 travels over a pothole, speed breaker, broken road, road joint or uneven surface, the rear suspension moves and the sway bar links repeatedly articulate. During cornering, the sway links also experience changing mechanical loads as the suspension responds to movement of the vehicle body. Over extended use, the existing anti roll link rods can gradually develop joint wear and unwanted clearance, which may contribute to knocking, clunking, tapping or rattling noises from the rear suspension. When proper inspection confirms that the original components are worn, installing correctly matched replacement links helps restore the mechanical connection within this section of the stabilizer system. Stokes Germany focuses on premium steering and suspension replacement components for European vehicles, with emphasis on dependable construction, accurate fitment and practical replacement value. According to the manufacturing and sourcing information provided for Stokes Germany, the brand works with established manufacturing sources across Germany, Poland, Russia, Turkey and England, supporting its European-quality positioning. Customers searching for rear sway bar links, sway links, anti roll link rods, anti-roll bar links or stabiliser sway links can therefore consider Stokes Germany as a premium replacement choice. Selecting a quality replacement component is only one part of a correct suspension repair, so the existing links should first be confirmed as worn and the anti-roll bar bushes, suspension arms, suspension bushes, dampers and mountings should also be inspected. Correct installation is equally important for dependable operation. For this Mercedes-Benz CLA C118 application, the supplied OEM reference is A2473205300. This number should remain unchanged and should always be checked against the complete VIN and exact vehicle specification before ordering. When the OEM reference and VIN confirm compatibility, this Stokes Germany set provides a premium European-quality replacement solution for the applicable Mercedes-Benz CLA C118 rear stabilizer-link application.
What is the function of rear stabilizer link rods in a Mercedes-Benz CLA C118?
The rear stabilizer link rods in a Mercedes-Benz CLA C118 perform an important function within the rear suspension system because they provide the mechanical connection between the relevant suspension components and the rear anti-roll bar while still allowing normal suspension movement. These components are also commonly called rear sway bar links, sway links, anti roll link rods, anti-roll bar links and stabiliser sway links. When the Mercedes-Benz CLA C118 travels over normal roads, potholes, speed breakers, broken surfaces, road joints or uneven roads, the rear wheels continuously move according to changes in the road surface and the stabilizer links articulate as part of the suspension system. During cornering, suspension movement on one side can differ from movement on the opposite side, creating changing mechanical loads through the stabilizer system. The anti-roll bar works as part of the suspension to help manage excessive body movement, while the stabilizer links provide the mechanical connection required for the bar to operate together with the moving suspension. Because these rear sway bar links work whenever the suspension moves, their joints experience thousands of repeated movements throughout normal vehicle use. They are also exposed to vibration, road impacts, dirt, moisture and changing suspension loads. Over extended mileage, these operating conditions can gradually create mechanical wear and unwanted clearance inside the joints. Once excessive joint play develops, a worn link may contribute to knocking, clunking, tapping or rattling noises from the rear suspension, particularly when the CLA C118 is driven slowly over potholes, rough roads or speed breakers. Replacing genuinely worn anti roll link rods helps remove unwanted movement caused specifically by these components and restores the proper mechanical connection within this section of the rear stabilizer system. Replacement should be considered restoration of normal suspension operation rather than a performance modification. Rear anti-roll bar bushes, suspension arms, suspension bushes, dampers, mountings and related hardware should also be inspected when diagnosing suspension noises because these components can create similar symptoms. For this Stokes Germany product, the supplied OEM reference is A2473205300. Always verify this number against the complete 17-character VIN and exact Mercedes-Benz CLA C118 suspension specification before ordering or installation.
How long do rear stabilizer link rods normally last on a Mercedes-Benz CLA C118?
There is no single fixed mileage or number of years after which every Mercedes-Benz CLA C118 must have its rear stabilizer link rods replaced because the actual service life of these components depends heavily on road quality, total mileage, driving conditions, driving style, suspension condition, environmental exposure and the amount of impact experienced during everyday driving. Rear stabilizer links should therefore normally be treated as condition-based suspension components rather than parts that automatically require replacement at one predetermined mileage. A Mercedes-Benz CLA C118 driven mainly on smooth highways may place less impact stress on its rear sway bar links than another CLA regularly driven over potholes, broken city roads, rough surfaces and large speed breakers. Every time a rear wheel moves upward or downward, the sway links move as part of the stabilizer system. During cornering, the anti roll link rods also experience changing mechanical loads because suspension movement on one side can differ from movement on the opposite side. Over thousands of kilometres, repeated articulation, road vibration and pothole impacts can gradually create mechanical wear. Dirt, moisture and deterioration around protective components can also influence their long-term service life. This explains why two Mercedes-Benz CLA C118 vehicles with similar mileage can have completely different stabilizer-link conditions. One vehicle may still have links in acceptable mechanical condition while another may already have developed excessive joint clearance or deterioration. Mileage alone should therefore not determine whether replacement is necessary. Physical inspection provides a much better indication of component condition. Knocking, clunking, tapping or rattling noises from the rear suspension are common reasons to inspect the rear sway links, particularly when these sounds become noticeable over potholes, rough roads or speed breakers. A technician should check the links for excessive joint movement, damaged protective components, loose mounting points, deterioration, corrosion or physical damage. If one link shows significant wear, the opposite-side link should also be inspected because both normally experience similar overall mileage. When both components show comparable deterioration, replacing them as a pair can be practical. The surrounding rear suspension should also be inspected because anti-roll bar bushes, suspension arms, suspension bushes, dampers and mountings can independently produce similar noises. Therefore, the actual mechanical condition of the rear stabilizer links should determine replacement rather than an assumed universal mileage interval.
Can replacing worn rear stabilizer links improve the handling and stability of a Mercedes-Benz CLA C118?
Replacing genuinely worn rear stabilizer links can help restore normal suspension response and handling consistency in a Mercedes-Benz CLA C118 when the existing components have developed excessive joint clearance, deterioration or physical damage, but standard replacement stabilizer links should not be considered a performance upgrade because their primary purpose is to restore the mechanical connection required by the original suspension system. The rear anti-roll bar works as part of the vehicle's suspension system, while the rear sway bar links provide the connection between the bar and the relevant suspension components. During normal driving, the rear suspension continuously responds to changes in the road surface. When the CLA enters a corner, vehicle weight naturally transfers and suspension movement on one side can differ from movement on the opposite side. The anti-roll bar works as part of the suspension system to help manage excessive body movement, while the sway links provide the mechanical connection required for the system to operate. When these links remain in good mechanical condition, they maintain this connection while allowing the required suspension movement. After extended use, however, repeated articulation, road vibration, pothole impacts and changing suspension loads can gradually create unwanted clearance inside the joints. A badly worn anti roll link rod may therefore reduce the consistency of this mechanical connection and may contribute to knocking, clunking, tapping or rattling noises from the rear suspension. When inspection confirms that the stabiliser sway links are genuinely worn, replacing them removes unwanted movement caused specifically by those components. As a result, the rear suspension may feel more solid and consistent compared with how it felt when significant joint wear was present. This should be understood as restoring normal suspension function rather than increasing the Mercedes-Benz CLA C118's handling capability beyond its intended specification. If the existing links are already mechanically sound, simply fitting another standard replacement set should not produce a major improvement. Overall handling and stability also depend on suspension arms, bushes, dampers, springs, tyres, wheels, steering components and wheel alignment. Therefore, if the CLA feels unstable, loose or unusual during cornering, the complete suspension should be inspected instead of assuming the rear stabilizer links are the only cause.
How can I confirm that Stokes Germany A2473205300 rear stabilizer links are correct for my Mercedes-Benz CLA C118?
The safest way to confirm whether Stokes Germany A2473205300 rear stabilizer links are correct for your Mercedes-Benz CLA C118 is to verify the OEM reference together with the complete 17-character VIN and exact vehicle suspension specification before ordering because selecting Mercedes-Benz suspension components only from the model name, production year or product photograph is not sufficiently precise. Start by confirming that your vehicle belongs to the Mercedes-Benz CLA C118 model family and obtain the complete VIN from the vehicle or registration documentation. The VIN should then be checked through an appropriate Mercedes-Benz electronic parts catalogue or provided to an experienced Mercedes-Benz spare-parts specialist. The rear stabilizer-link OEM reference returned for the exact vehicle should be compared carefully with A2473205300. This is particularly important because vehicles belonging to the same CLA C118 family can have differences according to drivetrain, production specification, suspension package and other vehicle-specific equipment. If the original stabilizer links remain installed, their identifying markings can also be checked wherever visible. If the original components have already been removed, a technician can additionally compare their overall dimensions, mounting arrangement, joint positions, thread details and physical construction with the replacement links. However, visual comparison should only be treated as an additional check because two suspension components can look almost identical while having different dimensions or applications. Customers should also remember that this component may be described as a rear stabilizer link, rear sway bar link, sway link, anti roll link rod, anti-roll bar link, stabiliser sway link or coupling rod depending on the catalogue or manufacturer. Different terminology does not automatically mean it is a different component. OEM-number matching therefore provides a stronger method of identification than relying on the product name alone. The correct process is to confirm the CLA C118 chassis, check the complete VIN, identify the rear suspension specification and compare the vehicle-specific OEM number against A2473205300. If all information matches, the Stokes Germany set can then be selected for the applicable vehicle. This VIN-first approach reduces the risk of incorrect ordering, unnecessary returns, additional workshop labour and installation problems.
Why is Stokes Germany a European-quality alternative to Lemförder, FAG, FEBI Bilstein and Meyle for Mercedes-Benz CLA C118?
Reviews
There are no reviews yet.